Peugeot 208 Key Replacement
Peugeot 208 key replacement should be left to experienced auto locksmiths with the right tools and know-how. They can make and program new keys much faster than a dealership would and at a lower cost.
A dead coin battery is most likely to be the cause the reason why your key fob isn't locking or unlocking doors. There are also other reasons that the key could be malfunctioning.
Dead Coin Battery
A dead coin battery can hinder your Peugeot 208 from locking or unlocking and won't start the engine. If this is the scenario, you'll need make use of the backup starting procedure that's described in your vehicle's owner manual.
The spark plugs may also be worn out. The spark plugs are responsible for igniting the fuel that powers the engine. However they are limited in their time of life. They'll eventually fail in the event that they aren't utilized enough.
Luckily, there's an easy solution to this issue. Examine the voltage of your battery using a multimeter. If it's lower than 11.5 volts, then you need to replace it. It is also essential to clean the battery's contacts when it has corrosion. This can be done by lifting the rubber covers that protect the two terminals on the battery and using wire brushes to clean any corroded areas of the battery. Then, you must reconnect the positive and negative pole cables.
Water Damage
If your 208 does not start and the battery has not gone flat, you should examine the spark plugs. It is possible that they're overly dirty, causing them to not to spark. This can be easily corrected by cleaning the spark plugs in an workshop.
Peugeot automobiles are equipped with a transponder that is compatible with the immobiliser. This ensures that only the right key can turn the engine. If the chip inside the Peugeot key is damaged, then it won't transmit the correct signal to the vehicle.
This is a very common issue that can be caused by water damage. This is particularly common in colder climates, as the vehicle may have been exposed to rain or snow. In this situation, contact an experienced locksmith who will have the required tools and equipment to modify the key. They also have the latest technological know-how and machinery required to make the Peugeot 208 smart key. The process should not take more than 15 minutes.
Contacts for the battery that are defective
Peugeot replaced the transponder chips using a new type that uses electronic components that are mounted on a circuit board. The new system is effective when it's brand new, but as time passes, the circuit boards begin to deteriorate and stop working correctly.
This could prevent the immobiliser chip activating and causing your car to not start. If this happens it's a good idea get in touch with a Peugeot specialist or locksmith.
A common issue occurs when the battery in the key fob starts to die. This causes the blade of the key to stop feeding into your lock. A car locksmith will replace the battery, and then cut a new key blade for you. This is a simple solution.
Faulty Receiver Module
It could be that the receiver module has a problem in the event that your Peugeot key fob doesn't work after being dropped on the floor, exposed to a sudden rainstorm or accidentally washed. The receiver is responsible for sending radio frequency signals to the onboard computer, which is responsible for controlling the centralized locking system inside your Peugeot vehicle.
The KeyLab on the key fob prevent water from getting to the electronic chip. However, prolonged exposure to water may be able to penetrate these seals and cause damage to the chip. The high salt content in the ocean water or pool can cause damage to the key fob, especially if it is submerged.
If your Peugeot spare key fob stops working it is necessary to have the module replaced. This can only by done by an Peugeot specialist or an expert auto locksmith. Like other automobiles, Peugeot keys are protected by an unique immobilizer system that requires the correct coding in order to start the engine. This is the reason that you should only trust an authorized Peugeot locksmith to create and program a replacement.
Computer with a problem on board
The on-board computer in your Peugeot is responsible for many of the systems within the car, from airbags to power windows. The on-board computer will display the code when something goes wrong. This code will be stored in the system until the issue is fixed. Most often, this involves replacing the onboard computer.
The most common reason for the warning light for the airbag to come on is corroded or loose connections in the sensor. It can be due to wear and tear, ageing, or exposure to salt and moisture. This issue needs to be taken care of as soon as you can, as an airbag malfunctioning could pose a risk in the event of an accident.
If your Peugeot is showing a card that is not being detected error, then the battery inside the key fob may be weak or dead. This could prevent the key fob from sending a signal to disable your vehicle's immobilizer. You can test this by pressing the unlock button on the key fob, then trying to start your vehicle. If this doesn't work the battery on the key has to be replaced.